F30 A/C noise

image Ok your probably thinking what the hell is this,,,F30 N20 A/C lines going to the firewall,,,bolting up to the expansion valve.image And here is the high side switch and shredder valve,,,,ok hear is where I’m going with this,,,,customer complained about a whistling /beeping sound coming from the center dash area,,,, only happens when fan speed on low and A/C button off,,,,and temp setting at 60′,,,,radio off and car must be sitting outside in the heat,,,,,guess what I heard it,,,,it’s is a beeping noise coming from the center vents.image Will look at what the fix is from BMW ,,,yes the high pressure A/C line from the expansion valve to the front condenser,,,,,do you notice something differ on the new A/C line,,,,yes that is a valve to shut off the pressure inside the line,,,it is a electrical valve that we have to splice into the harness to activate it when the A/C system is off.image Here the valve built into the line,,,this whole thing doesn’t make any sense and you will see at the end of this blog.so I install this fix it all A/C line as BMW what’s us too.image Here the A/C line installed,,,here where that valve sits right under the heater hoses,,,so I charge the A/C system back up and test drive the car just like the customer said,,,,,and guess what the dam noise is still there,,,,son of bitch,,,,lol,,,so now I have to make a puma case and tell them it didn’t fix the problem,,,now they want me to put a A/C compressor in the car for the fix,,,,,well so far so good,,,no noise after putting in the A/C compressor.

This entry was posted in Uncategorized and tagged , , , , . Bookmark the permalink.

14 Responses to F30 A/C noise

  1. kr4va says:

    wow weee its not even October fest

    Like

  2. KONG KING WAI says:

    Hi BMW TECHNICIAN.IM FAI FROM MALAYSIAN.I HAVE BMW F30 .CAUSE THE BLOWER MOTOR MAKING NOISE SO I OPEN THE BLOWER JUST CLEAN UP ONLY.THEN I JUST FIX BACK THE BLOWER BUT THE BLOWER NO WORKING SO HOW?

    Like

  3. amanda says:

    How do you trouble shoot Code 2 efe electric fan ?

    Like

    • I have seen that code before and that’s for the electric fan issue.

      Like

    • I’m sorry I didn’t read your question correctly,,,,to trouble shot you would have to see if your electric engine fan is working correctly ,,,,but that is difficult to find out,,,,so you just have to trust the fault code is correct, ,,,,lol,,,,what happens is the DME will pick up a signal that the engine fan is not turning on when it should be on so the DME throws a fault telling you that the engine fan is not working properly

      Like

  4. Learner says:

    Hello,
    I have come across the fault below on the 320i (F30):

    Central Gateway Module (ZGW) (ZGW_01)
    1 fault CD0487
    ZGM: Synchronisation process for FlexRay failed

    When it was investigated at the dealer the fault was removed from the memory (in the past), but this year the CD0487 fault has reappeared again, against mileage reading of -1 (not sure what -1 means?), do you know the potential cause and any solution(s) to this fault? Also is it worth investigating this fault further and any outer symptoms to be aware of with this?

    Many thanks

    Like

    • Question what is the problem we are having,,,,or is this just a fault you found in your car?,,,,We see that fault a lot,,,,it just a random fault that pop up once an awhile,,,the mileage reading of -1 tells me that it’s a random fault and it happened at mile 1,,,,so there might be something going on but at this time it’s just coming up with a random fault,,,,I would wait if some other fault may appear,

      Like

  5. Learner says:

    Hi, thanks for the reply. it is just a fault code that appeared in the car. The only outer symptom which I don’t know is related or not is a fan noise that is heard from the head unit (HU) area when the car is turned off, this seemed to be due to the cooling fan of the IDrive (hence normal operation of fan from the HU) after it was investigated at the dealer. They deleted the fault from memory which was the outcome required following their system (or process). As the fault has now reappeared again would you advise having it investigated further or should we ignore this? I am just concerned if it’s coming from ZGM (Central Gateway Module) whether could there be an ECU or wiring issue? When you see this fault at -1 mileage does that mean it is constantly occurring in the background or has it occurred just the once in that particular instance? Also do you know if this fault code is a sign the FlexRay communication or ZGM ECU is experiencing a serious issue or minor issue (in terms of the synchronisation) ?

    Like

    • I would just ignore this fault,,,,if it was something major it would say no communication or no signal,,,,this fault is probably coming from the ZGM and the -1 mileage is just a random thing because it doesn’t know what’s going on for that split second,,,,don’t worry about for now.

      Like

      • Learner says:

        Thanks for the quick reply, to clarify in terms of the ECU as this module is important to the car, does this mean this CD0487 fault is not a sign that the ZGM ECU (Central Gateway Module) itself is failing or on its way out ? And if that was ever the case would there be a different type of fault code you would expect or you could easily tell from an outer symptom ?

        Like

      • This is not a sign that the ZGM is failing,,,,if the ZGM was failing you would have other faults related to it.

        Like

  6. Learner says:

    OK many thanks and thank you for the service you provide to help people.

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.